品牌/型號：juyou
加工定制：是
品牌：juyou
一、用途 APPLICATION
本系列電汽熱水柜適用于船舶鉆井平臺上生活用淡水管系，以電和蒸氣作為加熱源，可獨立工作，具有自動調節功能，可將水溫控制在一式兩定的范圍之內，并配有安全裝置。
WITH ELECTRIC/STEAM AS THE HEATING RESOURSE，THIS SERIES OF HEATER IS APPLICABLE FOR LIFE USE FRESH WATER PIPE SYSTEM IN VESSEL AND WELL-DRILLING PLATFORM，IT CAN BE WORK INDEPENDENT，WATER TEMPERATURE IN A CERTAIN SCALE，PROVIDED SAFETY RELIEF DEVICE.
二、蒸汽加熱面積及加熱水量 HEATING AREA AND CAPACITY
三、電加熱功率及加熱水量HEATING POWER AND CAPACITY
電加熱功率 Heating power kw | 進出水溫 in/out water Temperature ℃ | 加熱水量 Heating capacity Kg/h | 電源 Power source |
12 | 15/65 | 180 | 440v,60Hz Or 380v,50Hz |
24 | 15/65 | 360 | |
36 | 15/65 | 540 |
四、電氣控制原理如下 ELECTRIC ConTROL PRINCIPLE DIAGRAM AS FOLLOWING
五、熱水柜組成 STEAM HEATER IS ConSIATED OF
1.溫度表 tem.gauge 2.安全閥 safety 3.壓力表 pre.gauge
4.電加熱器 electric heating unit 5.蒸汽加熱器 steam heating unit
6.絕緣包裝 insulation 7.排污閥 drainage valve 8.銘牌 name aplate
9.溫度控制器 tem.controller 10.本體 body
11.蒸汽溫度調節閥 steam tem.adjusting valve
六、安裝調試及維護 INSTALLATION DEBUGGING & MAINTENANCE
1.根據電汽熱水柜的支座預制安裝支架，水柜可裝在甲板或倉壁上，支座與支架之間應以3mm的硬橡膠或鋁板作襯墊，以防劇烈震動。
PREFIABICATE INSTALLING SUPPORT ACCORDING TO THE FOUNDATION OF THE STEAM WATER HEATER，IT CAN BE FIXED TO THE DECK OR THE WALL，FILLHARD RUBBER OR LEAD PLATE 3mm IN THCKNEAA BETWEEN THE SUPPORT AND FOUNDATION TO PREVENT VIOLENT SKOCK.
2.故障 BREAKDOWN
（1）法蘭處漏水 FLANGE LEAK
擰緊螺帽或更換密封墊片墊圈
TIGHT THE NUT OR CHANGE THE PRESSURE FITTING FLAKE OR GASKE.
（2）閥桿閥件四周漏水 LEAK AROUND POLE AND VALVE
壓緊松動螺帽，填料太薄，加厚填料擰緊螺帽。閥體內有雜物，閥體磨損，清洗閥體閥腔并更換。
NOT ENOUGH FITTING OR VALVE STEAM NUT LOOSE THEN FITTING ADDING FITTING AND TIGHING NUT，AND SUNDRY THINGS IN VALVE BODY OR VALVE DAMAGED，CHEAN THE BODY AND INSIDE OF THE VALVE OR CHANGE IT.
七、隨機文件 DOCIMENTS ATTACHED
1.總圖 GENERAL DRAWING
2.產品質量證明書 PRODUCT QUALITY GUARANTEE
3.船檢證書 TESTING CERTIFICATE
4.質量反饋單 USER SHEET-PRODUCT QUALITY MESSAGE
5.裝箱單 LIST OF GOODS
6.使用說明書 INSTRUCTION BOOK
八、貯存 STRORE
電汽水柜應放在干燥的室內貯存。
THE STEAM HEATER SHOULD BE STORED IN DRY ROOM.
證書：可提供各大船級社船檢證書
